Calculate The Rate Of Flow Of Glycerine Of Density  through The Conical Section Of A Pipe, If The Radii Of Its Ends Are 0.1 M And 0.04 M And The Pressure Drop Across Its Length Is 10 N/m2.

Why Kaysons ?

Video lectures

Access over 500+ hours of video lectures 24*7, covering complete syllabus for JEE preparation.

Online Support

Practice over 30000+ questions starting from basic level to JEE advance level.

Live Doubt Clearing Session

Ask your doubts live everyday Join our live doubt clearing session conducted by our experts.

National Mock Tests

Give tests to analyze your progress and evaluate where you stand in terms of your JEE preparation.

Organized Learning

Proper planning to complete syllabus is the key to get a decent rank in JEE.

Test Series/Daily assignments

Give tests to analyze your progress and evaluate where you stand in terms of your JEE preparation.

SPEAK TO COUNSELLOR ? CLICK HERE

Question

Calculate the rate of flow of glycerine of density  through the conical section of a pipe, if the radii of its ends are 0.1 m and 0.04 m and the pressure drop across its length is 10 N/m2.

Solution

Correct option is

According to continuity equation,  

   

and according to Bernoulli’s equation for horizontal tube, 

           

  

Substituting the value of v2 from eq. (i) in (ii)  

          

  

So rate of flow through the tube  

          

              

              .

SIMILAR QUESTIONS

Q1

The vertical of a mass ball of mass M and density d1, when dropped in a container filled with glycerine becomes constant after some time. If the density of glycerine is d2, the viscous force acting on the ball will be

Q2

To what height should a cylindrical vessel be filled with a homogeneous liquid to make the force with which the liquid passes on the side of the vessel equal to the force exerted be the liquid on the bottom of the vessel?

Q3

 

The density of air in atmosphere decreases with height and can be expressed by the relation:  

           

Where  is the density at sea-level, A is a constant and h is the height. Calculate the atmospheric pressure at sea-level. Assume g to be constant. 

Q4

 

A rod of length 6 m has a mass 12 kg. It is hinged at one end at a distance of 3 m below water surface. (a) What weight must be attached to the other end of the rod so that 5 m of the rod are submerged? (b) Find the magnitude and direction of the force exerted by the hinge on the rod. 

(Specific gravity of rod is 0.5).

Q5

 

A large block of ice 5 m thick has a vertical hole drilled through it floating in the middle of a lake. What is the minimum length of a rope required to scoop up a bucket full of water through the hole?

[RD of ice = 0.9]

                                                                              

Q6

 

A cubical block of iron 5 cm on each side is floating on mercury in a vessel. Water is poured into the vessel so that it just covers the iron block. What is the height of water column? 

[RD of Hg = 13.6 and Fe = 7.2] 

Q7

A glass beaker having mass 390 g and an interior volume of 500 cm3 floats on water when it is less than half filled with water. What is the density of the material of the beaker?

Q8

 

A block of wood weighs 12 kg and has a relative density 0.6. It is to be in water with 0.9 of its volume immersed. What weight of a metal is needed if the metal is attached below the wood?

[RD of metal = 14]  

Q9

A wooden stick of length L, radius R and density  has a small metal piece of mass m (of negligible volume) attached to its one end. Find the minimum value of the mass m (in terms of given parameters) that would make the stick float vertically in equilibrium in a liquid of density 

Q10

A non-viscous liquid of constant density 1000 kg/m3 flows in a streamline motion along a tube of variable cross-section. The tube is kept inclined in the vertical plane as shown in figure. The area of cross-section of the tube at two points P and Q at heights of 2 metre and 5 metre are respectively  the velocity of the liquid at point P is 1 m/s. Find the work done per unit volume by the pressure and the gravity forces as the fluid flows from point P to Q.